Sun Spritz™ Tanning Booth Installation

Installation Information, Requirements and Responsibilities

Included with the Sun Spritz™ system we provide component installation and training collateral for your salon. The salon is responsible for being prepared for the Sun Spritz™ system prior to its installation. The following are basic requirements and things that MUST BE COMPLETED prior to system installation arrival on-site:

Dedicated room with minimum dimensions of 7’ x 7’(84” x 84”)with the ceiling a minimum of 8’ high for unit only, empty and accessible

Electrical service (120 VAC outlet) 20 Amp Service with 4Plex Outlet or Duplex Outlet with Outlet

Strip operational and properly located

For a unit with a changing room allow a minimum of 7’ x 12’(84” x 144”) of space with an 8’ ceiling

Fresh water with shut off (cold) and drainage piping installed in the room and ready for use

Planned location of air compressor (dedicated 120 VAC, 20 AMP outlet required)

Remote timer location (without changing room)

Step ladder (6 foot) available for installers use

Timer network wires or wall jack in room

Shop Vac

Salon access from 7:00 am until normal salon closing hour

System shipment, unloading and storage

Time dedicated for proper system training of salon manager and employees

Dedicated Room

The Sun Spritz™ system should have a dedicated room for its use only. The room must be at a minimum of 7’ x 7’ (84” x 84”); slightly larger is always better. The room floor must be level and free of obstructions. Preferred floor cover type is tile or linoleum, carpeted floors are not recommended.

Overhead lighting is also required, the system is not provided with lights.

Electrical Service

The Sun Spritz™ unit requires a 220 VAC electrical service for operation. A standard 3plex electrical outlet is sufficient for proper operation or a standard Duplex Outlet with Outlet Strip. Under no circumstances will installers be responsible for electrical service installation.

Fresh Water – Drain

A fresh water supply is required for booth sanitizing and wash-down after each tanning session. Cold-water service is required with a minimum of 40 pounds of pressure capable of 8 gpm. Water service needs to be quipped with an on/off valve located in the room with easy access. We recommend that water service to the Sun Spritz™ system be turned off each night. Although the system is fully self-contained, a drainpipe is required to remove wash-down water from the booth. The Sun Spritz™ system is equipped with a fully automatic discharge pump for the removal of wash-down water. The discharge pump provided is capable of overcoming 70 ft. of head pressure or approximately 30 PSI. A minimum drainpipe inside diameter of 3/8” is required. Drainage should be directed to the sewer system. In no way what so ever is Sun Spritz™ responsible for the integrity of the hoses or piping installed for fresh water and drain service. Under no circumstances will installers be responsible for fresh water or drainpipe installation. The unit utilizes 3/8 OD High Pressure Plastic Hose from the unit attaching to supply by a Quick-Connect fitting. The final connection will require the Quick-Connect fitting with 1/4” MIP. being threaded into the customer supplied 1/4” FIP. fitting with a shut off valve.

Note: In an existing salon a normal clothes washer cold water supply and drain can be accessed. The plastic 3/8” lines will need to be pre-run before delivery. (1-for cold water supply and 1 for wash down water drain.)

Customer is aware that he/she will be responsible for running and locating all wiring pertinent to the Sun Spritz™ and it’s timing system and modem. Yes

Customer is aware that he/she is responsible for and maintenance of all plumbing required for the Sun Spritz™.

All water supply connections must be in place prior to installation. 100 feet of plastic water supply hose will come with each unit upon delivery, (the plastic water supply hose can be shipped prior to delivery of your Sun SpritzTM unit). It is the sole responsibility of the salon owner to have adequate water supply connections in place prior to installation and delivery.

No other hose, except that which is provided should be connected to the Sun Spritz™. Usage of unapproved hose or connectors will void warranty.

We recommend a qualified plumber test incoming water pressure at the spigot and provide outcome to salon owner.

Water pressure must be between 40-60 PSI.

Customers’ responsibility!

Customer claims sole responsibility for any/all modification to the facility. Installation personnel will not make modifications of any kind. (Door openings, wall. etc.)

True Exposure Tanning - Instant Tropical Tan Look Approved by the Federal Drug and Food Administration .